Aeroseal Duct Sealing – FAQs

Q: What size of holes can be sealed using the Aeroseal air duct sealing process?
A: Holes and cracks up to 5/8 inch wide can be completely sealed.

Q: What does the Air Duct Diagnostic and Inspection tell me?
A: Inspection discovers any obvious break in the duct work and, as the initial step of the sealing process, the Aeroseal system will establish an exact amount of leakage in the duct system. Of course, many people already know that a room or two in their house doesn’t get good air circulation because they can feel it. Or they already know that their energy bill is high because they see it. The diagnostic measurement provides a scientifically valid means to understand the performance of your air duct system.

Q: What are the estimated savings?
A: Some homeowners have saved up to 40 percent on their energy bill. Naturally, exact savings are difficult to precisely estimate since they depend on a multitude of variables such as your weather, house condition and design, your heating and air conditioning system, system usage – as well as other factors like energy prices.

Basnett Plumbing, Heating, AC & Electrical Aeroseal air duct certified technicians are qualified to run a program made by the Environmental Protection Agency (EPA) called "Duct Investor". Duct Investor takes a comprehensive list of variables and provides a homeowner with the best available estimate of what they should realize in cost savings.

Q: In a nutshell, how does an Aeroseal air duct seal work?
A: Aeroseal duct sealing works in the following ways:

  • Preseal test to measure the leakage as a baseline for measuring progress.
  • Block off the registers with foam or plastic.
  • Inject an UL tested and approved aerosol into the duct system.
  • Since the air has no place to go except out through the leaks (the registers are blocked), the sealant material is deposited precisely at the air duct holes or cracks where leakage occurs.
  • A computer and sensors are used to measure and control the progress. The technology is patented from the University of California and the process is endorsed by the Environmental Protection Agency.
  • Postseal test to measure improvements.
  • Complete report and certificate printed on the spot to provide a record of improvements.

Q: Does the air duct sealing material become brittle?
A: The vinyl sealing material remains rubbery, never cracking.

Q: How long will the air duct sealing material last?
A: The sealing material has been found in rigorous testing to last over 10 years without failure.

Q: Do air ducts need to be cleaned before air duct sealing?
A: It’s likely that the holes and cracks in the ductwork have allowed dust and other particulate matter to enter the system. If you are experiencing extensive levels of household dust, this might be the reason. In most instances, duct cleaning is not found to be required prior to Aeroseal sealing. Your Aeroseal contractor can advise whether it will be necessary to clean your ductwork prior to sealing.

Q: Can ducts be cleaned after Aerosealing?
A: Ducts of all types can be cleaned after Aerosealing.

Q: What if my ducts are hidden from view?
A: Unlike other sealing methods, Aeroseal can seal ducts that are hidden. Aeroseal can seal all types of ducts.

Q: Does the sealant coat the inside of the ductwork?
A: The sealant only sticks to the holes in the air duct without coating the rest of the duct.

Q: Is the sealing material used by the Aeroseal air duct sealing system safe?
A: The sealant material consists of a water–based solution (65 percent water) prior to application. The dried sealant material primarily contains two chemicals, vinyl acetate polymer (VAP) and 2–ethyl–1 hexanol (2E1H). The vast majority of what is left in the duct system is VAP, which has been used in water–based paints, adhesives, and hair spray. VAP has been used in chewing gum, and has no OSHA Exposure Limit. 2E1H is a common industrial solvent and is not considered toxic by OSHA. A review of the literature showed no ill effects after long–term exposure to concentrations of 200 ppm. The largest concentration of 2E1H measured in test houses was 1 ppb (200,000 times smaller), during Aeroseal injection. The sealant is UL–listed for smoke generation and flame spread (UL 723 0,0), and additional testing by UL showed no signs of mold growth or erosion.

Q: Does the sealant leave an odor?
A: At the time of application there is a very mild odor, similar to that of craft glue. However, that dissipates within a few hours. The Aeroseal air duct sealing process leaves no lingering odor, and since the material does not put off gas over time, there will be no odor for the life of the product.

Q: Will it harm my electronics? Pets? Artwork?
A: No. Our technicians are trained to protect all sensitive objects in the home.

Q: If the rooms of my home have inconsistent temperatures, can Aeroseal improve the performance of my heating and A/C system(s)?
A: The Aeroseal sealing system can help improve the comfort of your home by reducing the difference in temperature levels throughout your home.

Q: Can the Aeroseal air duct sealing system help reduce my utility bills?
A: Some homeowners have saved up to 40 percent of their energy bills after having the Aeroseal air duct sealing system seal their central air duct system. A typical homeowner should expect to see measurable reduction in energy use for heating and cooling.

Q: Can the Aeroseal air duct sealing system reduce the noise made by the return and supply grilles in my home?
A: This noise is usually the result of two conditions. One is created when the ductwork is undersized and air is rushing through your air duct system. The other condition is caused when a limited amount of air is allowed to flow through the indoor coil of your heating and cooling system. Once the exact problem has been identified, Basnett Plumbing, Heating, AC & Electrical can provide the best solution for noise reduction.

Q: Can the Aeroseal air duct sealing system reduce the amount of dust in my home?
A: Ductwork runs through attics, crawlspaces, basements, garages, and walls. Leaking return air ducts pull in dust and other indoor air pollutants and sends them to the central heating and cooling system. From there they sent to the living areas of your home. The Aeroseal air duct sealing system can reduce the amount of leakage by as much as 90 percent, reducing dust and other indoor air pollutants from the conditioned air in your home.

Need Service?

Contact the experts at Basnett Plumbing, Heating, AC & Electrical.
Call us at 978-431-2906!